0845 10 80 685

01403 700 794

Ergo Non-Electric Water Softener 15mm FullFlow Install Kit 1000mm Hoses

In Stock
£ 945.00
£ 655.00
  1. #Product Info#

    Shop now for the Ergo Non-Electric Water Softener complete with a 15mm Full Flow Installation Kit (1000mm Hoses). 

    This softener is compact yet has a 8 litre vessel, ensuring you have plenty of soft water for busy households, making the softener more efficient and using less salt.
    With a speedy 15 minute regeneration and easy to use salt loader that will take 4 blocks of salt or tablet salt.

    This option comes complete with a discounted 15mm Full Flow Installation Kit worth £70.00!
    Click here to see whats included. 


     Single Tank, Simplex, Softener.
     It runs entirely on water pressure - no electrical supply required for easy installation
     Connection with by-pass: 3/4 " BSP Connections
     Water consumption per regeneration 25 litres
     Flow rate at 1 bar max. 2100 L / h
     Working Pressure : >1-8 bar
     Temperature max. 40 º C
     Blending Valve included on Softener
     Water required for regeneration: 25 litres
     Regeneration Time: 15 minutes
     Salt for regeneration: 0.36kg

  2. #Dimensions#
    Height (back) - 506mm
    Depth - 498mm
    Width - 293mm

  3. #Which Installation Kit?#
    It is important that you select the correct installation kit to suit your pipework and hot water system in your property. This avoids any chance of the incorrect installation kit from restricting the flow. If you have conventional gravity fed, or indirect, system which has a cold water tank in the loft space and hot water cylinder, then the standard 15 mm kit would be suitable.

    If you are still on 15 mm pipework but have a combination boiler, or direct type system, then you are better to go with the 15mm full flow installation kit. This has the benefit of using uprated fittings and connection hoses and ensures that you get a minimum of 15 mm bore through everything and therefore get no restriction on flow.

    If you have 22mm pipework, then the best choice is the 22mm high flow install kit. This is found on the majority of houses less than 10 years old and is generally used on feeding mains fed unvented hot water systems.  If you are unsure, then please call us on 0845 10 80 685 or email for clarification.


    Installation of you water softener - DIY or plumber?

    Every softener comes complete with full installation instructions, these can also be found under the brochure tab. This allows for simple installation by a plumber or someone keen on DIY. If you are unsure, call us for clear impartial advice on 0845 10 80 685 (local call rate) or 01403 700794 or email us

  4. #Warranty#

    The owner of a Fountain Softeners water softener is protected by the following guarantees, which include the right to exchange or repair in the case of a manufacturer’s defect for up to:

    3 Years Parts
    3 Years Labour

    The guarantees are under condition that the softener is installed according to local regulations and to the manufacturer’s instructions as well as the following:

    1) It is very important that the water temperature of 50 degrees centigrade is never exceeded.

    2) There must always be suitable salt in the brine tank.

    3) The electrical supply to the Water Softener should be maintained 24 hours per day.

    4) After a power outage the current time of day simply needs to be reset.

    5) The inlet and outlet valves must always be open. The by-pass valve must always be closed.

    6) It is recommended that the Water Softener is serviced every two years.

     If irregularities should occur, you would need to:-

    Isolate the power supply to the unit.
    Close the inlet and outlet valves and open the bypass valve.
    Contact Fountain Softeners customer services.